Search results for "Stress concentration"
showing 10 items of 39 documents
Finite element analysis of stress concentration between surface coated implants and non surface coated implants - An in vitro study.
2019
Background To determine qualitative comparison in stress distribution between surface coated implants and non surface coated implants using 2 different lengths and vertical, oblique, and lateral forces. Material and Methods 3 dimensional finite element study was carried out at first molar site with 4 surface coated and 4 non surface coated implants using mimic 8.11, solid edge 2004, hypermesh 9.0, and ansys12.1 software. Results The pattern of stress distribution was almost similar between vertical and oblique loading but varied with lateral loads between surface coated and non surface coated implants. As the length of the implants increased stress concentration had no significant variation…
Strain rate dependence for evolution of steady state grain sizes: Insights from high-strain experiments on ice
2019
Abstract Understanding of the microstructural evolution and equilibrium grain size development during steady state tertiary flow is essential in order to improve our knowledge of ice and rock deformation. This contribution presents results from in situ transmitted light deformation experiments of natural glacier ice, with the development of the microstructure in a tertiary flow regime. We conducted one relative slower ( 1 × 10 − 6 1/s) and two relative faster-strain rate ( 2 × 10 − 6 1/s) pure shear experiments at −10 °C, up to a shortening of ∼57%. Microstructure development was followed by time-lapse observations, and two new microstructure-based indicators, the ‘seeding rate’ and the ‘mi…
Stress concentration for closely located inclusions in nonlinear perfect conductivity problems
2019
We study the stress concentration, which is the gradient of the solution, when two smooth inclusions are closely located in a possibly anisotropic medium. The governing equation may be degenerate of $p-$Laplace type, with $1<p \leq N$. We prove optimal $L^\infty$ estimates for the blow-up of the gradient of the solution as the distance between the inclusions tends to zero.
The use of steel angles for the connection of laminated glass beams: Experiments and modelling
2012
Abstract In the present paper the experimental results relative to three-point bending tests on multilayer glass beams and on semi-rigid connections realised with stainless double web angles are presented and discussed. Small and medium size glass beams were tested and load–deflection curves and crack patterns at failure were recorded. The laminated glass specimens, of equal cross-section, were characterised by three different combinations of annealed float and fully thermally tempered glass plies and different interlayers. Steel joints constituted by double web angles to connect two glass beams were tested adopting several geometrical configurations and using stainless steel bolts preloade…
Molecular-dynamics study of copper with defects under strain
1998
Mechanical properties of copper with various types of defects have been studied with the molecular-dynamics method and the effective-medium theory potential both at room temperature and near zero temperature. The loading has been introduced as constant rate straining and the dynamics of the process region of fracture is purely Newtonian. With the model three types of defects were studied: point defects, grain boundary, and an initial void serving as a crack seed. Point defects were seen to decrease the system strength in terms of fracture stress, fracture strain, and elastic modulus. Due to random microstructure, highly disordered systems turned out to be isotropic, which on the other hand …
Fatigue crack growth through particulate clusters in polycarbonate material
2011
The interaction of a crack with a perfectly bonded inclusion or a cluster of inclusions in polycarbonate matrix was investigated through both numerical simulations and fatigue tests. Stress intensity factors (K(I)) were evaluated by boundary element method for several particle sizes, position and finally for inclusion cluster as a precursor study for the experiments. The numerical simulation has shown the crack tendency to circumvent the inclusions with consequential reduction of the growth rate. Fatigue crack growth tests were carried out on several particle-filled specimens at constant value of the applied stress intensity factor range (Delta K(Iapp)) highlighting the crack delay due to t…
NUMERICAL-EXPERIMENTAL METHOD FOR THE ANALYSIS OF RESIDUAL STRESSES IN COLD-EXPANDED HOLES
2012
Hole cold expansion is a technique widely used to improve the fatigue life of components with holes, e.g. bolted or riveted joints. As it has been demonstrated in literature by analytical, numerical and experimental analyses carried out by several authors, the compressive residual stresses introduced by the hole cold expansion have a beneficial influence on both the static and the fatigue strength of the treated component, because they reduce significantly the typical stress peaks around the hole due to stress concentration. In the literature, various analyses of the residual stresses introduced by the hole cold expansion have been performed by using several methods such as X-ray diffractio…
Effect of steel collars on the seismic behaviour of axially-cracked historical stone columns
2014
Granite and heavy stone circular columns could often be found in the cultural heritage among ancient churches and historical buildings in all the Mediterranean area. Their good strength properties allow them to carry big load values, while their bright colours and aesthetical characteristics were used by a lot of architects in the past to achieve structural solutions with great visual impact.Though such materials have great compressive strength values, environmental effects, especially long term effects, can damage the structural members, by cracking them. In this way the slenderness of the column increases, and the presence of an imposed ground motion can be very dangerous, since the colum…
A Thermodynamic Plasticity Formulation with Local and Nonlocal Internal Variables
2002
In order to obtain the elastic response of nonhomogeneous materials, it is often sufficient to adopt an implicit homogenization technique which allows one to treat the material as an equivalent continuum medium. For large stress concentration or for accurate small scale studies this widely applied technique may show some limit and a more refined analysis might be required involving nonlocal elastic effects, see e.g. Kroner (1967), Eringen et al. (1977).
Fatigue Design of Cruciform Joints including V-notch Effect at the Weld Toe
2014
Abstract The present paper proposes a new and more accurate fatigue life prediction model for fillet welded joints in steel subjected to constant amplitude loading. With the traditional fracture mechanics approach, the greatest difficulty when computing the fatigue life of a welded detail is to determine the initial crack size a0. The classical way to determine the stress intensity factor K (SIF) is by using the following formula Where σ is the applied stress, a is the crack size and g(a/T) the geometrical correction factor which has been determined by Gurney function or similar solutions. This approach is not accurate for short crack because of the singular V-notch behaviour close to the c…